S804 Abend

An error occurred when the system tried to process an EC, EU, LC, LU, VC, or VU form of the GETMAIN macro. A reason code in the SDWACRC field of the system diagnostic work area (SDWA) explains the error:Check out IEA705I message for more details

Reason codeExplanation
04

There is not enough virtual system queue area (SQA) storage available to satisfy the request.

08

There is not enough virtual common service area (CSA) storage available to satisfy the request.

0C

There is not enough virtual local system queue area (LSQA) storage available to satisfy the request.

10

There is not enough virtual private area storage available to satisfy the request.

14

A negative amount of storage was specified on the GETMAIN.

1C

During request processing, the system tried to get LSQA virtual storage for virtual storage management’s (VSM) cell pool. There was not enough LSQA virtual storage available.

20

There is not enough virtual storage in the LSQA to build a new address queue anchor table (AQAT) stack.

View all Abend Codes

S805 Abend

An error occurred when the system tried to process an EC, EU, LC, LU, VC, or VU form of the FREEMAIN macro. A reason code in the SDWACRC field of the system diagnostic work area (SDWA) explains the error:Check out IEA705I message for more details

Reason codeExplanation
18

A negative amount of storage was specified on the FREEMAIN macro.

1C

During request processing, the system tried to get local system queue area (LSQA) virtual storage for virtual storage management’s (VSM) cell pool. There was not enough LSQA virtual storage available.

20

There is not enough virtual storage in the LSQA to build a new address queue anchor table (AQAT) stack.

View all Abend Codes

S806 Abend

The supervisor, or the Supervisor Call (SVC) for the BLDL (build a directory entry list) macro, detected an error during the processing of a LINK(X), XCTL(X), ATTACH(X), or LOAD macro with the EP (entry point) or EPLOC (EP location (address)) operand.The reason code in register 15 identifies the error: Check out IEC222I message for more details

Reason codeExplanation
04

The system could not find the module, whose entry point is the value of the EP or EPLOC operand, in the indicated library (private library, job library, or link library). This situation can occur when LSEARCH=YES is specified on the macro and the limited library search fails to locate the module. For an alias name, ensure that the entry point attributes match that of the load module which was previously loaded (that is, authorization, RMODE, entry point displacement).

08

An uncorrectable I/O error occurred when the BLDL control program routine attempted to search the directory of the library that contained the program whose entry point was specified in the EP or EPLOC operand. This can occur if the specified library is an uninitialized partitioned data set (PDS). An incorrect data extent block (DEB) has been detected by the BLDL control program. The DEB was built in other than protect key 0 through 7.

0C

The supervisor attempted to search a library for the program that the EP or EPLOC operand specifies and found that the library data control block (DCB) is not open.

10

A program issued a LOAD macro with the explicit load option, but there is no DCB parameter. For explicit loads, the program must supply the DCB parameter with the macro because the system searches for the module that the LOAD specifies only in the library that the DCB parameter specifies.

14

The system could not find the module, whose entry point is the value of an EP or EPLOC operand of a XCTL(X) macro, in the link pack area (LPA), which is where the module must be when the module is requested by an SVC routine.

18

An SVC routine issued a XCTL(X) macro for a module. The system tried to search the link pack area directory to find the module, but the directory had not as yet been built.

1C

The data control block (DCB), included as part of a LINK(X), LOAD, XCTL(X), or ATTACH(X) macro is incorrect.

20

Internal error.

View all Abend Codes

S80A Abend

An error occurred when the system tried to process an R form of the GETMAIN or FREEMAIN macro. A reason code in the SDWACRC field of the system diagnostic work area (SDWA) explains the error: Check out IEA705I message for more details

Reason codeExplanation
04

There is not enough virtual system queue area (SQA) storage available to satisfy the request.

08

There is not enough virtual common service area (CSA) storage available to satisfy the request.

0C

There is not enough virtual local system queue area (LSQA) storage available to satisfy the request.

10

There is not enough virtual private area storage available to satisfy the request.

1C

During request processing, the system tried to get LSQA virtual storage for VSM’s cell pool. There was not enough LSQA virtual storage available.

20

There is not enough virtual storage in LSQA to build a new address queue anchor table (AQAT) stack.

View all Abend Codes
suggestion / complaint / feedback Web Statistics